H P
3 0 0 0 B u s i n e s s S e r v e r s
N e t w o r k i n g
Features
HP SNA Services (30292B):
- SNA NRJE Network Remote Job Entry
- SNA IMF/iX Interactive Mainframe Facility
- LU 6.2 Application Programming Interface
- SNA Distributed Host Command Facility/iX
•
•
SNA NRJE is able is able to
communicate with JES2, JES3, and
VSE/POWER host job entry subsystems.
Automatically route job output based
on destinations selected by the user at
the time of job submittal - “Job
Management”
•
Automatically route output based on
user-selected IBM host forms - “Output
Management”
SNA NRJE Network Remote Job Entry
•
•
Process batch jobs originated by a user
on an IBM Mainframe - “Reverse NRJE”
Provide Native Languages Support - for
data only. NLS 16-bit character
mapping; interactive and programmatic
access; and data integrity are not
supported for languages such as
Japanese, Korean, Simplified Chinese,
and Traditional Chinese.
This paragraph describes System Network Architecture
Network Remote Job Entry (SNA NRJE) for both the
MPE V (SNA NRJE/V) and MPE/iX (SNA NRJE/iX)
operating systems. The term SNA NRJE is used to refer
to both SNA NRJE/V and SNA NRJE/iX. The terms SNA
NRJE/V and SNA NRJE/iX are used when a distinction is
necessary.
•
Host output can be sent to any
supported output device on an HP
3000 such as disk files, tape files,
printers, or user-written programs.
Multiple HP 3000 users can
concurrently access the host for batch
processing.
Jobs are submitted into the
SNA NRJE/V on the HP 3000 Series 37-70 or SNA
NRJE/iX on the HP 3000 Series 900 provides enhanced
batch data communications between the HP 3000 and an
IBM Systems/370-compatible mainframe in a System
Network Architecture (SNA) environment. SNA NRJE
emulates the major features of an IBM 8100 DPPX/RJE
workstation using an SNA Physical Unit Type 2 (PU 2),
Logical Unit Type 1 (LU 1) device.
•
•
transmission queue independent of the
line status.
MVS/SP
VSE
•
•
•
•
•
•
•
Users can submit jobs and receive
output without operator intervention.
Other HP 3000 applications run
concurrently with SNA NRJE.
SNA NRJE can share an SNA link with
other HP SNA service products.
Customizable error and help message
facilities are provided.
Host console commands can be sent
and host console data can be received.
Data compression and character code
translation are configurable.
SNA NRJE and SNA Link support
communications at up to 56 KB/s on
MPE V and 16 MB/s on MPE/iX.
SNA NRJE can take advantage of
SNA/SDLC Link’s Auto-dial capability.
JES2 or JES3
ACF/VTAM
VSE/POWER
ACF/VTAM
IBM Host Processor
or
Communications
Controller
Modem
Modem
Up to 56 Kbps for MPE/V,
and 64 Kbps for MPE/iX
9600 bps
~
~
~
~
Switched
or Leased
Modem
Modem
HP 3000 V or iX
SNA NRJE
and SNA Link
IBM 8100
DPPX/RJE
Disks
Card Readers
Printers
Card Readers
RJE Console
Terminals
Magtapes
Printers
Disks
Magtapes
•
Laser Printers
Printer
~
~
HP
HP 3000
3000
Bus ness
Servers
3
The Output Management feature of SNA
NRJE allows users to have job output routed
based on the form selected by the user’s host
JCL and a Lookup Table which provides a
mapping between host form names and HP
3000 file equations. Again default forms will
be used if none are indicated.
Product Requirements
Both SNA NRJE/iX and SNA NRJE/V require an
IBM System/370-compatible mainframe (Model
370, 30xx or 43xx) with an IBM 37xx
communications controller. The following
software must be running on the host and
communications controller:
Reverse NRJE allows a user connected to an
IBM mainframe (or a user on a separate HP
3000 attached to the IBM) to start a job on an
HP 3000 if SNA NRJE on the HP 3000 is
active.
• Job Entry Subsystem: JES2 or JES3
running under
– Operating System: MVS
or
• Job Entry Subsystem: VSE/POWER
running under
– Operating System: VSE
– ACF/VTAM
Note: The user must use the special form
CMD that causes SNA NRJE to stream a
received data set rather than route the data
set using file equation attributes.
– ACF/NCP
Using SNA NRJE and SNA Link, an HP 3000
with an HP 2680 Laser Printer can act as a
remote or local (though still requiring a 37xx
communications controller) print station for
an IBM host. HP 3000 users can direct print
output data sets to the laser printer. Users
can specify an environment file that indicates
predefined forms, character fonts and formats
- data set by data set.
Selected User Commands
Command
Function
ALTER*
Revises the priority of a submitted
job, or jobs.
CANCEL*
Cancels previously submitted jobs
and causes data sets returning from
transmitted jobs to be deleted.
DISPLAY
EXIT
Provides information about a
workstation.
Causes the user to exit from the
NRJE command interpreter (CI), and
returns control to the process from
which the CI was run.
Native Language Support allows users to
select alternative Native Language Ids for
translation of user data. Only data going to
the host or coming from the host will be
translated, commands and messages will still
be in native 3000. Each reader, printer, and
punch can be configured with a different
language. NLS 16-bit character mapping;
interactive and programmatic access; and data
integrity are not supported for languages such
as Japanese, Korean, Simplified Chinese, and
Traditional Chinese.
##FD
“File Definition” used within a job to
include the contents of the file
specified in the command.
HELP
Provides you with information about
subsystem commands.
NRJE
Invokes the subsystems command
interpreter. It is also an NRJE sub
system command, so that you can
switch to a different default
workstation.
REDO
Modifies and executes the previous
NRJE subsystem command.
RUN
Executes a prepared program.
SHOW*
Provides information about jobs
you have submitted.
SUBMIT
Prepares a batch input job stream for
transmission to a host system.
* This command has NRJE Manager extensions.
HP
3000
Bus ness
Servers
4
HP will support certain versions, releases,
modifications, and Product Temporary Fix
(PTF) levels of the above software. The
Network Implementations Support Plan
(NISP) will help the customer engineer
determine support requirements in advance of
SNA NRJE in a particular network.
Installation and Configuration Policy
SNA NRJE is customer installable. However,
Hewlett-Packard will perform minimum
configuration of SNA NRJE in order to verify
minimum product functionality. These tasks
performed by HP are included in the product
purchase price.
SNA NRJE/iX Product Requirements
• An HP 3000 Series 900 computer system
running a supported release of MPE/iX.
• HP 30291A SNA/SDLC Link/iX, J2249A
SNA/Token Ring Link/iX, or HP 30298A
SNA/X.25 Link/iX
For product configuration tailored to the
customer’s specific needs, or for a complete
HP implementation, HP offers a
comprehensive range of integrated and
flexible support services. Please refer to the
Network Support data sheets in this guide for
more information on these services.
SNA NRJE/V Product Requirements
• An HP 3000 Series 37-70 and MPE V operat-
ing system
Customer Responsibility
• HP 30246A SNA Link/V
Prior to having HP personnel onsite to
perform minimum configuration of SNA NRJE,
the customer is responsible for the following:
Functional Specifications
SNA NRJE provides the HP 3000 with the
major functions of an IBM 8100 DPPX/RJE
workstation operating as a remote node in an
SNA network.
• Providing HP with the information neces-
sary to complete the Network
Implementation and Support Plan (NISP)
including:
– System configurations
– Logical network map identifying relevant
traffic flow
The maximum RU size supported by NRJE is
768 bytes.
SNA NRJE supports a record length up to 252
bytes (or characters) for JES2 and JES3 and
128 bytes (or characters) for VSE/POWER
when sending data from the HP 3000 to an
IBM host. Records up to 225 bytes in length
may be received from the host.
– Physical network map identifying relevant
network hardware components.
• Verifying that the necessary host mainframe
software is installed and configured to sup-
port SNA NRJE. The customer should con-
tact their HP Sales Representative for typi-
cal host parameter values or consult the
“HP SNA Products Remote System
Configuration Guide (J2220-61025).
• Verifying that SNA Link/V, SNA/SDLC
Link/iX, SNA/Token Ring Link/iX, or
SNA/X.25 Link/iX is properly installed and
configured prior to the installation of SNA
NRJE unless an SNA Link will be installed
at the same time.
NRJE supports up to eight workstations, each
of which may support up to 16 LU-LU
sessions, with a maximum of 64 total LU-LU
sessions.
HP
3000
Bus ness
Servers
5
• Updating the HP 3000 system to the proper
release level and installing the SNA NRJE
software using AUTOINST. Refer to the
HP 3000 MPE/iX Installation and Update
Manual (36123-90001) for MPE/iX systems
or the HP 3000 Software Update Manual
(32033-90036) for MPE V systems.
HP effort spent on problems that are not
caused by HP installation and configuration
activities is considered HP Consulting Support
and is billable to the customer at normal HP
time-and-materials rates.
System Environment
• Verifying that all of the necessary software
modules have been successfully installed by
AUTOINST and are at the correct version
levels using the NMMAINT.PUB.SYS utility.
• Performing full system backups as neces-
sary and ensuring that the HP 3000 system
and personnel with HP 3000 system man-
agement knowledge are available when HP
is onsite to complete the INP card installa-
tion and minimum configuration of SNA
NRJE.
SNA NRJE/iX, SNA SDLC Link/iX, and
SNA/X.25 Link/iX are available on the HP
3000 Series 900 with currently supported
releases of the MPE XL or MPE/iX operating
system. SNA/Token Ring Link/iX requires
MPE/iX release 5.0 or later. SNA NRJE/V and
SNA Link/V are available on the HP 3000
Series 37-70 computers with the MPE V
operating system.
Documentation
The customer is also responsible for
completing the configuration in order to fully
integrate SNA NRJE into the existing
The following documentation is for both SNA
NRJE/V and SNA NRJE/iX:
customer network after HP has completed the
minimum configuration of the SNA NRJE.
• 30292-61001 SNA NRJE User Programmer
Reference Manual
HP Responsibility
• 30292-61000 SNA NRJE Node Manager’s
Guide
Following the installation of SNA NRJE, HP is
responsible for the following:
• J2220-61025 HP SNA Products Remote
System Configuration Guide
• 5958-8544 HP SNA Products: Job Entry
Subsystem (JES) Guide
• Confirming that all of the necessary soft-
ware modules have been installed and are at
the correct version level.
• Configuring the SNA NRJE product to a
minimum configuration (1 LU) in order to
verify software and hardware functionality.
• Verifying the SNA NRJE configuration by
issuing the NRJECONTROL START com-
mand and ensuring that the LU-to-LU ses-
sion becomes active.
These steps complete HP’s portion of the
installation and minimum configuration of
SNA NRJE.
HP
3000
Bus ness
Servers
6
Features
SNA IMF/iX Interactive
Mainframe Facility
•
•
•
SNA IMF/iX and an SNA Link product
allow the HP 3000 to emulate the base
function set of an IBM 3270 control unit
using SNA (PU2 or 2.1, LU1, 2, 3)
protocols.
The SNA Interactive Mainframe Facility/iX (SNA IMF/iX)
product provides IBM 3270 device emulation for
Hewlett-Packard terminals, printers, and HP 3000 Series
900 systems. (SNA IMF/V, P/N 30247A, provides similar
functionality for MPE V systems.)
Other HP SNA service products can all
be supported simultaneously over one
SNA/SDLC Link/iX or SNA/X.25 Link/iX.
The maximum datacomm line speed is
64 KB/s.
SNA IMF/iX on an HP 3000 Series 900 allows interactive
communications between the HP 3000 and an IBM
System/ 370-compatible mainframe using SNA 3270
protocols. SNA IMF/iX emulates the base function set of
an IBM 3270 control unit using SNA Physical Unit Type
2 (PU2 or 2.1), Logical Unit Types 1,2,3 (LU1, 2,3)
protocols. HP terminals, printers, and applications on
the HP 3000 running SNA IMF/iX emulate IBM terminal
and printer functions.
SNA IMF/iX supports up to 127 devices
(terminals, printers, and application
programs) concurrently. With MPE/iX
Release 4.0 or later, SNA IMF/iX
supports up to 127 devices per SNA Link.
•
•
The Pass Thru capability of SNA IMF/iX
allows HP 3000-attached printers and
terminals to emulate the base function
set of IBM 3270 printers and terminals.
SNA IMF/iX allows access to 3270 subsystems on the
mainframe (such as TSO, CICS, and IMS) through a set
of high-level intrinsics. There are two modes of
operation. In programmatic mode, customer-written
application programs on the HP 3000 emulate IBM 3270
terminals and printers, exchanging data with the host
SNA IMF/iX Pass Thru takes advantage
of the Modified Data Tag feature of
selected HP terminals (such as the HP
700/94) and supports a write
optimization feature that limits screen
updating to modified rows only. These
features significantly reduce response
time.
IBM Mainframe
ACF/VTAM
•
SNA IMF/iX provides a “rolling softkeys”
feature that allows the user to define
and label multiple levels of terminal
function keys to be their most
Processor
Communications
ACF/NCP
Controller
frequently used IBM 3270 program
function keys. Users can also define
various “menus” of function keys that
are clearly displayed in the terminal
screen. The SNA IMF Programmer’s
Reference Manual documents the
terminals supporting this feature, some
of which provide up to 16 softkeys on
the screen at a time.
SNA Link(s)
SNA
IMF/iX
Other HP
SNA Services
IBM 3274
Control Unit
HP 3000/iX
•
Terminals/printers being used in the
PassThru mode do not have to be
dedicated. The user may access either
the HP 3000 or the remote host from
the same terminal.
Up to 127 SNA IMF/iX Devices
– HP Terminals
– HP 3000 Programs
– HP 3000 Printers
Up to 32 IBM Devices
– IBM Terminals
– IBM Printers
HP
3000
Bus ness
Servers
7
applications via intrinsics. The customer’s application
program decides which intrinsics to call. In Pass Thru
mode, an HP-written application program on the HP
3000 also emulates IBM 3270 terminals and printers,
exchanging data with host applications via intrinsics. In
Pass Thru mode, the selection of which intrinsics to call
is fixed.
Features (continued)
•
SNA IMF/iX allows programs on an
HP 3000 to communicate with
programs o the host system, through
a set of high-level intrinsics.
Programs may be written in C,
FORTRAN, COBOL, COBOL II, BASIC,
Pascal, or SPL.
SNA IMF/iX requires the installation and use of
SNA/SDLC Link/iX (30291B), SNA/Token Ring Link/iX
(J2167B)* or SNA/X.25 Link/iX (36939B). The SNA
Link products manage the physical link to the host and
implement protocols in the lower three layers of SNA.
•
•
•
Most host application programs
designed to work with IBM 3270
terminals can usually be used with
minimal change.
SNA IMF/iX runs concurrently with
other HP 3000 applications and can
be accessed from other systems via
HP’s Network Services.
* SNA/Token Ring Link/iX (J2167B) requires MPE/iX
release 5.5 Express 7 or later, or MPE/iX release 6.0
Express 1 or later.
SNA IMF/iX supports HP’s Native
Languages Support (NLS 8-bit
character mapping), which allows
application programmers to create
local language applications for end
users. NLS 16-bit character mapping;
interactive and programmatic access;
and data integrity are not supported
for languages such as Japanese,
Korean, Simplified Chinese, and
Traditional Chinese.
Asian options also supported include:
• HP Asian Vectra PCs
• HP Asian Terminals
• HP Asian Printers
• Asian IBM environments
Functional Description
SNA IMF/iX is a software product that allows an
HP 3000 and attached devices to emulate the base
function set of an IBM 3274 control unit and attached
devices, which does not include graphics, programmed
symbols, color, or extended highlighting.
•
•
SNA IMF/iX supports IBM applications
with 480, 1920, or 3440 character
screen sizes.
For Asian options only:
–
SNA IMF/iX (ASIAN) supports
IBM’s DBCS protocol to ensure 16-
bit data integrity communication
between the HP 3000 and the
Asian host.
SNA IMF/iX (ASIAN) allows both
16-bit interactive as well as
programmable access to the
Asian IBM host.
SNA IMF/iX (ASIAN) provides 16-
bit character mapping between
the HP (HP-15) and the IBM
(DBCS) data.
SNA IMF/iX (ASIAN) supports
languages such as Japanese,
Korean, and Traditional Chinese.
SNA IMF/iX requires SNA/SDLC Link/iX, SNA/Token
Ring Link/iX or SNA/X.25 Link/iX. These links manage
the communications link and implement lower-level SNA
(PU2 or 2.1) protocols. SNA IMF/iX provides interactive
and programmatic 3270 communications with a
mainframe and can run simultaneously along with other
SNA services such as SNA NRJE/iX and LU6.2 API/iX on
MPE/iX systems.
–
–
–
In the programmatic mode, user-written programs on
the HP 3000 can communicate with programs on the
host. HP 3000 programs may be written in C,
FORTRAN, COBOL, COBOL II, BASIC, Pascal, or SPL.
HP
3000
Bus ness
Servers
8
Program access is accomplished through use
of a set of intrinsics that are powerful
procedures, which perform the low-level task
of decoding the data streams.
written for use with IBM 3270 controllers will
work with SNA IMF/iX with little or no
modification. For customers who are in the
process of changing from centralized to
distributed processing, this feature helps
provide a smooth transition.
(Table 1 provides a list of available intrinsics.)
The intrinsics can be used with the intrinsics
of other HP 3000 facilities such as
IMAGE/3000, VPLUS/3000, KSAM/3000, or
NS/3000. The high-level, easy-to-use nature
of these intrinsics results in improved
programmer productivity.
The Pass Thru mode of SNA IMF/iX provides
users the capability of using HP 3000 attached
printers and DTC attached terminals for
interactive access to a host computer.
In this mode, SNA IMF/iX users can directly
access host software such as CICS or IMS, or
they can use TSO for program development.
Because programmatic mode works by
exchanging information through screen
images, most host applications that have been
Table 1. SNA IMF/iX Intrinsics Summary
Intrinsic
Function
ABORT3270
ACQUIRE3270
Aborts an outstanding no-wait REC3270 or TRAN3270 request.
Provides the SNA IMF/iX users the capability to start PASS Thru on an HP 3000 terminal
or printer programmatically.
ATTRLIST
CLOSE3270
ERR3270
EXTFIELDATTR
FIELDATTAR
IOWAIT3270
IODONTWAIT3270
OPEN3270
Returns the locations of attribute characters with all or a subsection of a screen.
Equivalent to turning off the specified device.
Returns the error message associated with a given intrinsic error number.
Returns information about the attribute information of the Double Byte
Returns information about the attributes of the specified field.
Informs the user program that a previous I/O operation has completed.
Waits for a previous no-wait I/O request to complete.
Equivalent to turning on the power of a 3270 Display Station or Printer. It allocates the
internal screen buffer used by SNA IMF/iX.
PRINT3270
READFIELD
Prints a copy of the internal screen image to a spool file.
Reads a field of data from the internal screen buffer and returns the data to an
HP application program.
READSCREEN
Reads all or part of the internal screen buffer and returns this data to the
HP application program.
RECV3270
Allows the user program to receive the screen after modification by the host.
Equivalent to pressing the RESET key on an IBM 3270 Display Station keyboard.
Returns information about the attributes of the screen image currently in the internal buffer.
Equivalent to typing a Series of keystrokes in a 3270 Display Station keyboard. Provides
a mechanism for performing “special function key” operations from the HP application
program. Also allows more than one field of data to be updated in one Intrinsic call.
RESET3270
SCREENATTR
STREAM3270
TRAN3270
Equivalent to pressing a transmit key in the 3277 or 3278 Display Station keyboard.
It causes modified data to be transmitted to the host the next time the host polls the device.
VERS3270
Returns the number if the version of SNA IMF/iX that is being executed in the HP 3000.
WRITEFIELD
Writes data from the HP application program into an unprotected field if the internal
screen buffer.
READSTREAM
WRITESTREAM
Reads all or part of the untranslated host data stream.
Creates the data stream that an HP application program sends to the IBM host.
HP
3000
Bus ness
Servers
9
Table 2.
3270 Typewriter Keyboard
Using the Pass Thru mode does not require
the use of dedicated terminals.
HP 700/96 Keyboard
Program Function Keys
User specifies by typing
desired program function
number or through user-
defined configuration of
HP function keys.
The Pass Thru mode of SNA IMF/iX is mot
intended as a replacement for real IBM 3270
devices.
FIELD MARK, TEST REQ,
CURSOR BLINK, ALT
CURSOR, IDENT, DEV
CNCL, DUP, CLOCK, PRINT
and CURSOR SELECT
Keys
No equivalent on HP
terminals
For HP terminals being used in the Pass Thru
mode, the response time will be longer than
that of IBM terminals:
• The data transmission rate between the
HP 3000 and the terminals is slower than
that between the IBM 3270 controller and
its attached terminals.
• For terminals not supported by the write
optimization feature, the screens on the
HP 3000 and Pass Thru terminals are
rewritten any time a change is made. For
small changes, this contributes to an
increase in response time
• SNA IMF/iX uses the Modified Data Tag fea-
ture of the HP 700/94, HP 2394A, and HP
150 terminals in order to accurately and
flexibly handle null and blank characters. In
addition, this may result in improved
response time when compared to other HP
terminals.
PA1, PA2, PA3, CLEAR,
SYSTEM REQUEST
Keys are in different
locations (Softkeys are
used)
SYSTEM AVAILABLE,
INSERT MODE, INPUT
INHIBITED Indicators
ERASE INPUT, ERASE
EOF, TAB, BACKTAB,
NEWLINE, RESET INSERT
Keys
Indicators not provided
Equivalent functions
provided
3270 Characters
Corresponding to HP
Terminal Characters
cent sign ¢
!
solid vertical bar |
“NOT” sign
[
]
!
^
• For applications where response time is
critical, please consult your HP Sales
Representative for more information.
• Although the principle functions of IBM
3270 terminal keyboards are implemented -
including Program Function (PF) keys and
Program Attention (PA) keys - there are
some differences:
unprotected field by replacing the field with
exactly the same characters as it had previ-
ously; the field would NOT be transmitted
to the host with SNA IMF/iX, since no char-
acters had changed. A real 3270-type ter-
minal will transmit such modified fields
whether or not any characters are actually
changed.
• Some keys are in different positions, some
keys have different labels, and some keys
are not implemented. Table 2 lists the
major differences between IBM 3270 termi-
nals and HP 2392 terminals.
• Leading blanks can be converted to nulls
based on a configuration option at Pass
Thru startup.
• Trailing blanks can be converted to nulls
based on a configuration option at Pass
Thru startup.
• Trailing nulls can be converted to blanks
based on a configuration optional Pass Thru
startup.
• Magnetic card reader, auxiliary card reader,
and light pen are not provided in HP termi-
nals using Pass Thru mode.
There are minor logical differences in the way
HP terminals behave. Differences include:
• With Pass Thru mode, only unprotected
fields in which one or more characters have
actually been changed are transmitted to
the host. If a Pass Thru user “modifies” an
HP
3000
Bus ness
Servers
10
• SNA IMF/iX does not support the numeric
lock feature.
• Pass Thru mode does not support slave
printers (printers attached to terminals).
50% performance improvement in Pass
Thru mode and greater functionality over
other terminals.
– HP 700/96
– HP Vectra
Functional Specifications
– PC with Reflection 7 PLUS Version 3.3
(or later)
• SNA IMF/iX emulates the base function set
of the IBM 3274 terminal controller; the
base set does not include color, graphics,
programmed symbols, or extended high-
lights.
• In Pass Thru mode, non-MDT terminals are
not supported with all host applications that
are sensitive to nulls and blanks. In these
circumstances, an MDT terminal will func-
tion properly and is strongly recommended
to be the terminal of choice.
• SNA IMF/iX supports communications to an
IBM System/370 (or compatible) mainframe
running either the MVS/SP, MVS/XA,
DOS/VSE, or VM operating systems with
ACF/VTAM through an IBM 37xx communi-
cations processor running ACF/NCP.
• SNA IMF/iX supports communications with
an IBM S/36 running SSP or an IBM/38 run-
ning CPF or an IBM AS/400 running OS/400.
• The SNA Link/iX product supports Physical
Unit Type 2 or 2.1 protocols; SNA IMF/iX
provides Logical Unit Type 1,2, and 3 emula-
tion over the link. The SNA Link/iX or
SNA/Token Ring Link/iX can support inter-
active (SNA IMF/iX and SNA DHCF/iX),
batch (SNA NRJE/iX), and programmatic
(LU6.2 API/iX) communications simultane-
ously over a single link to an IBM host.
• In Pass Thru mode, SNA IMF/iX emulates
the IBM 3278-2, 3278-3 and 3278-4 display
stations and IBM 3287 printers.
• The following terminals are supported with
HP 3000 MPE/iX systems in Pass Thru mode
via the DTC attachment.
– HP 700/92
– HP Vectra PC with Advance Link 2392
– HP Vectra PC Reflection 7 PLUS,
Version 3.3 (or later)
• SNA IMF/iX supports the write optimized
feature for improved performance in Pass
Thru mode with the following terminals:
–
HP 700/92
• With the HP X.25/iX Network Link (36939B)
and NS 3000/iX Network Services (36920B),
SNA IMF/iX supports these terminals when
they are directly attached to an HP 2334A
Plus or HP 2335 PAD.
This feature is supported on SNA IMF/iX or
SNA IMF/V (30247A) only and is NOT
supported on the IMF/V (30250A) product.
Other Pass Thru-supported terminals
configured to be one of the terminals listed
above are NOT supported.
• SNA IMF/iX supports up to 127 devices (ter-
minals, printers, or application programs)
concurrently per SNA link with MPE/iX
Release 4.0 or later.
• The HP 700/94 terminal is recommended for
use with SNA IMF/iX in Pass Thru mode as
it offers the greatest performance and func-
tionality. SNA IMF/iX also supports null
suppression mode on HP 700/94 terminals
which result in further performance
• The HP 700/94, HP 2394A, HP 150, HP
700/92, and HP 2392A terminals support a
19.2 KB/s connection to the HP 3000.
• The following terminals support multiple
levels of “rolling softkeys” allowing up to 96
user-definable function keys.
– HP 700/94
improvements.
• The following terminals support Modified
Data Tags and, consequently, provide a 10-
– HP 2394A
• SNA IMF/iX supports any HP system
printer.
HP
3000
Bus ness
Servers
11
• Link Level Message encoding:
– SNA IMF/iX supports both NRZ and
NRZI encoding.
• Access to the SNA IMF/iX intrinsics in pro-
grammatic mode is provided in capability-
mode as well as native-mode with the use of
HP-provided switch stubs.
• In Pass Thru mode, terminals configured as
consoles are not supported.
Installation and Configuration Policy
The customer is responsible for loading the
SNA IMF/iX software onto the system.
Hewlett-Packard will perform minimum
configuration of SNA IMF/iX in order to verify
minimum product functionality. This activity
is included in the product purchase price.
Product Requirements
Customer Responsibility
• SNA IMF/iX requires an IBM System/370 or
compatible mainframe (models 370, 30xx,
0r 43xx) with an IBM 37xx communications
controller. The following software must be
running on the IBM host and communica-
tions controller:
– MVS/SP, MVS/XA, DOS/VSE, or VM
– ACF/VTAM
– ACF/NCP
• For communications to an IBM S/36, IBM
S/38, or IBM AS/400 minicomputer, the fol-
lowing software must be running on the IBM
systems:
– SSP (S/36) Release 5
– CPF (S/38) Release 7.0
Prior to having HP personnel onsite to
perform minimum configuration of SNA
IMF/iX, the customer is responsible for the
following:
• Providing HP with the information neces-
sary to complete the Network
Implementation and Support Plan (NISP),
including:
– system configurations
– logical network map identifying relevant
traffic flow
– physical network map identifying relevant
network hardware components
• Verifying that the necessary host mainframe
software is installed and configured to sup-
port SNA IMF/iX. The customer should con-
tact the HP Sales Representative for typical
host parameter values or consult the
“HP SNA Products Remote System
Configuration Guide” (J2220-61025) for
details.
• Verifying that the SNA/SDLC Link/iX,
SNA/Token Ring Link/iX, or SNA/X.25
Link/iX is properly installed and configured
prior to the installation of SNA IMF/iX
unless the link product will be installed at
the same time.
– OS/400 (AS/400) Release 2 and the
HP 3000 must be running MPE/iX
Release 4.0 or later.
• HP will support certain versions, releases,
modifications, and PTF levels of the above
software. Your HP Sales Representative or
Systems Engineer can determine whether
SNA IMF/iX can be supported with your
particular configuration. The Network
Implementation Support plan (NISP) will
help the customer engineer determine sup-
port requirements in advance of the installa-
tion of SNA IMF/iX in a particular network.
• SNA IMF/iX Product Requirements
– HP 3000 Series 900 computer system
– HP 30291B SNA/SDLC Link/iX
or
• Updating the HP 3000 system to the proper
release level and installing the SNA IMF/iX
software using AUTOINST. Refer to the
HP 3000 MPE/iX Installation and Update
Manual (36123-90001).
– J2167B SNA/Token Ring Link/iX
– HP 36939B SNA/X.25 Link/iX
HP
3000
Bus ness
Servers
12
• Verifying that all of the necessary software
modules have been successfully installed by
AUTOINST and are at the
Network Startup includes implementation
scheduling and coordination assistance,
network configuration and verification testing,
and network documentation.
NMMAINT.PUB.SYS utility.
• Performing full system backups as neces-
sary and ensuring that the HP 3000 system
and personnel with the HP 3000 system
management knowledge are available when
HP is onsite to complete the minimum con-
figuration of SNA IMF/iX.
System Environment
SNA IMF/iX is available on all HP 3000 Series
900 systems with currently supported releases
of the MPE/iX operating system.
The customer is also responsible for
SNA IMF/iX requires installation and
operation of HP 30291B and A5563A
SNA/SDLC Link/iX, J2167B SNA/Token Ring
Link/iX, or HP 36939B SNA/X.25 Link/iX.
completing the configuration in order to fully
integrate SNA IMF/iX into the existing
customer network after HP has complete the
minimum configuration of SNA IMF/iX.
Support Products
HP Responsibility
HP offers a spectrum of support service
products to help plan, implement, operate,
and manage your multivendor network
throughout the network lifecycle.
Following the installation of SNA IMF/iX, HP
is responsible for the following:
• Confirming that all of the necessary soft-
ware modules have been installed and are at
the correct version level.
For more information, contact your HP Sales
Representative, or refer to the HP data sheets
for specific support services.
• Configuring the SNA IMF/iX product to a
minimum configuration in order to verify
software and hardware functionality.
• Verifying the SNA IMF/iX configuration by
issuing the RUN TTSSON.PUB.SYS com-
mand with the appropriate parameters and
entering the IBMTEST command. This test
verifies the LU to SSCP session.
Documentation
The following documentation is for SNA
IMF/iX:
• 30293-61000 SNA IMF/iX Node Manager’s
Guide
These steps complete HP’s portion of the
installation and minimum configuration of
SNA IMF/iX.
• 30293-61005 SNA IMF Programmer’s
Reference Manual
• 30293-61008 Using SNA IMF Pass Thru
• J2220-61025 HP SNA Products remote
System Configuration Guide
Additional Implementation
Assistance
• 30293-60211 SNA IMF/iX: User Support
Guide (For use in Taiwan)
For implementation needs that go beyond
installation, the customer can either provide
self-support or can purchase additional
services from HP. These services included
Network Startup and HP ConsultLine. In
addition, the customer can also purchase
service from HP on a time-and-materials basis.
• 30293-60221 SNA IMF/iX: User Support
Guide (For use in Japan)
• 30293-60231 SNA IMF/iX: User Support
Guide (For use in Korea)
HP
3000
Bus ness
Servers
13
Features
LU 6.2 Application Programming
Interface
•
•
•
•
•
•
•
•
•
HP LU 6.2 API provides:
High-level Intrinsics
Support for Major Languages
Support for IBM Applications
Multiple Sessions
Peer-to-peer Connectivity
Parallel Sessions
Support for Remote Attach
Compatibility with Other SNA
Services
This data sheet describes HP LU 6.2 API (Application
Programming Interface) for both MPE V and MPE/iX
operating systems. The term HP LU 6.2 API is used to
refer to both HP LU 6.2 API/V and HP LU 6.2 API/iX
products. The terms HP LU 6.2 API/V and HP LU 6.2
API/iX are used when a distinction is necessary.
HP LU 6.2 API/V on an HP 3000 Series 37 through 70 or
HP LU 6.2 API/iX on an HP 3000 Series 9xx provides HP
3000 users with a way to program HP 3000 application
programs for program-to-program communication in an
SNA environment.
•
•
•
Trace Facility
Logging Facility
User Controlled Sessions
Management from Program or CI
(CNOS
•
•
Enhanced Communication Rates
Efficient and easy-to-program prob-
lem detection and recovery proce-
dures.
As with all HP SNA services, cus-
tomized error and help facilities are
provided.
HP LU 6.2 API implements the LU 6.2 “mapped
conversation verbs” for what IBM has named “advanced
program-to-program communications” (APPC). Users
may write “transaction programs” that use these verbs
(or high-level intrinsics as HP has implemented them) in
order to communicate with each other, even though
these programs may be executing on different systems
within the SNA network.
•
•
X.25 Connectivity
IBM AS/400
IBM S/370 Mainframe
IBM S/370 Mainframe
CICS
OS/400
CICS
LU 6.2
LU 6.2
LU 6.2
Transaction Program
Transaction Program
Transaction Program
VTAM
VTAM
Parallel
Sessions
IBM Communications
Controller
IBM Communications
Controller
ACF/NCP
ACF/NCP
Node
Node
Type 2.0
Type 2.0
Node Type 2.1
Peer-to-Peer
SNA LU 6.2 Advanced
Program-to-Program
Communication
SNA LU 6.2 Advanced
Program-to-Program
Communication
SNA/SDLC Link/iX (Node Type 2.0 nd 2.1) or
SNA/X.25 Link/iX (Node Type 2.0 only) or
SNA/Token Ring Link/iX (Node Type 2.1)
SNA Link/V
LU 6.2 API/V
LU 6.2 API/iX
SNA
SNA
SNA
SNADS/iX
SNA IMF/V
SNA NRJE/V
LU 6.2 Transaction
Program
LU 6.2 Transaction
Program
IMF/iX DHCF/iX NRJE/iX
HP 3000 MPE/iX System
HP 3000 MPE/V System
HP
3000
Bus ness
Servers
14
for the HP 3000. These HP SNA products
may all be running simultaneously over the
same SNA Link/V, SNA/SDLC Link/iX,
SNA/Token Ring Link/iX* or SNA/X.25
Link/iX to the SNA network. The SNA Link
products manage the physical link to the
IBM host and implement protocols in the
lower three layers of SNA.
HP LU 6.2 API provides
• High-level Intrinsics: HP 3000 program-
mers can use a set of high-level intrinsics to
implement program-to-program communica-
tion in an SNA network.
• Support for Major Languages:
Application programs on the HP 3000 can
be written in COBOL II, Transact, or Pascal.
For LU 6.2 API/iX, C language applications
are also supported.
• Support for IBM Applications: HP LU
6.2 API supports Mapped Conversations
with CICS in an MVS or DOS/VSE environ-
ment and Mapped Conversations with
VTAM in an MVS environment. With
MPE/iX Release 4.0 or later, HP LU 6.2
API/iX supports Mapped Conversations in
an OS/400 environment.
• Multiple Sessions: An HP 3000 applica-
tion program using LU 6.2 API/V intrinsics
may have up to 8 LU-LU sessions running
simultaneously. With MPE/iX Release 4.0 or
later, an HP 3000 application program using
LU 6.2 API/iX intrinsics may have up to 256
LU-LU sessions running simultaneously.
Each session is responsible for a separate
communication task or for adding additional
bandwidth to a single communication task.
• Peer-to-peer Connectivity: With MPE/iX
Release 4.0 or later, LU 6.2 API/iX provides
peer-to-peer connectivity to an IBM
Note: HP LU 6.2 API/iX supports Native-
mode HP 3000 applications only.
• Trace Facility: An easy-to-use trace facili-
ty that allows HP 3000 application program-
mers to track all LU 6.2 intrinsic calls and
executions within applications being devel-
oped, serving as a valuable debugging aid
during program development.
• Logging Facility: A comprehensive logging
facility that records all online LU 6.2 API
session messages to aid in problem identifi-
cation and resolution.
• User Controlled Sessions Management
from Program or CI ( CNOS) : With
MPE/iX Release 5.5 Express 7 or later, or
MPE/iX Release 6.0 Express 1 or later,
Programmatic or interactive user-controlled
session management allows users to change
session limits (over Node Type 2.1).
• Enhanced Communication Rates: The
maximum datacomm line speed between
the HP 3000 and the IBM mainframe host is
56 KB/s on MPE V and 16 MB/s on MPE/iX.
• Efficient and easy-to-program problem
detection and recovery procedures.
• As with all HP SNA services, customized
error and help facilities are provided.
• X.25 Connectivity: HP LU 6.2 API/iX can
communicate to an IBM mainframe over an
X.25 connection. The SNA/X.25 Link/iX
product (HP 30298A) can be used in place
of SNA/SDLC Link/iX, or SNA/Token Ring
Link/iX* but SNA/X.25 Link/iX emulates a
Type 2.0 node, not a Type 2.1 node.
Therefore if you run LU 6.2 API/iX over
SNA/X.25 Link/iX, you cannot communicate,
peer-to-peer with a Type 2.1 node like an
IBM AS/400.
AS/4000 over Node Type 2.1. an HP 3000
may establish LU-LU sessions with an IBM
AS/400 over Node Type 2.1 without having
to go through a mainframe node.
• Parallel Sessions: With MPE/iX Release
4.0 or later, LU 6.2 API/iX provides support
for parallel sessions over Node Type 2.1. An
HP 3000 may establish multiple, simultane-
ous LU-LU sessions over a single LU-LU pair
over Node Type 2.1.
• Support for Remote Attach: Remote
Attach is the ability of a remote LU 6.2
application to start running and begin com-
munication with it.
• Compatibility with Other SNA
Services: The HP LU 6.2 API is completely
compatible with other SNA services offered
* SNA/Token Ring Link/iX requires MPE/iX
release 5.0 or later.
HP
3000
Bus ness
Servers
15
LU 6.2 API intrinsics are summarized in the
following table.
Functional Description
HP LU 6.2 API provides a set of high-level
intrinsics for application programmers to use
for program-to-program communication
between an HP 3000 application program and
an application program running on an IBM
host mainframe. HP LU 6.2 API/iX also pro-
vides communication to an IBM AS/400.
These intrinsics are responsible for initiating
LU 6.2 conversations so that data can be sent
or received over these conversations on behalf
of program pairs needing to communicate to
complete a “transaction.” Examples of trans-
action are database updates and file transfers.
LU 6.2 API consists of a set of user-callable
intrinsics that implement the set of LU 6.2
defined mapped verbs along with the follow-
ing option sets:
LU 6.2 API Intrinsics Summary
Intrinsics
Function
MCALLOCATE
Establishes a mapped conversation
between two TPs.
MCCONFIRM
Sends a confirmation request to the
remote TP and waits for reply.
MCDEALLOCATE Ends a mapped conversation
between TPs.
MCGETALLOCATE Receives the request from a remote
TP to start a conversation and then
establishes the conversation.
MCGETATTR
Returns information pertaining to a
mapped conversation.
MCFLUSH
Flushes the LU’s send buffer.
MCPOSTONRCPT Causes LU 6.2 API to post the con
versation when information arrives.
MCPREPTORCV Informs the remote TP that the
HP 3000 resident TP (the local TP)
is ready to receive data over the
mapped conversation.
MCRCVANDWAIT Waits for information to arrive on
the mapped conversation and then
receives the information. The
Option Sets
IBM-Defined Verbs
PIP data (both local
and remote support)
Flush the LU’s
send buffer
information can be data,
conversation status, or request
establishes the conversation.
MC_FLUSH
Prepare to receive
(including long locks) MC_PREPARE_ TO_ RECEIVE
MCRCVNOWAIT Receives any information available
on the mapped conversation with
out waiting.
MCREQTOSEND Notifies the remote TP that the
local TP is requesting to send data
for the mapped conversation.
MCSENDERROR Informs the remote TP that the
local TP has detected an error.
Post on receipt
MC_POST_ON_RECEIPT
Wait for posting
to occur
WAIT
Test for posting or
request-to-send
received
MC-TEST
Receive immediate
MC_RECEIVE_IMMEDIATE
MCTEST
Tests the conversation for the
receipt of information.
Get conversation
attributes
MC_GET_ATTRIBUTES
MCWAIT
Waits for the receipt of information
on one or more conversations.
HP
3000
Bus ness
Servers
16
If connecting to an IBM mainframe:
An HP 3000 Series 900 running a supported
release of MPE/iX. The SNA/SDLC Link/iX
product (30291A), SNA/Token Ring Link/iX
product (J2167B) or the SNA/X.25 Link/iX
product (36939B).
Product Requirements
Requirements for IBM mainframe hardware
and software are the same for both HP LU 6.2
API/V and HP LU 6.2 API/iX.
IBM Mainframe Hardware Requirements:
• An IBM System/370 mainframe. This may be
any IBM plug-compatible mainframe that
supports 370 architecture.
• A port on an IBM 37xx or compatible com-
munications controller that supports an
SNA line. The HP 3000 can also be con-
nected to the Communications Controller
via an IBM 3710 Network Controller.
(Please check with your HP Sales
If connecting to an IBM AS/400:
An HP 3000 Series 900 running MPE/iX
Release 5.5 or later operating system. The
SNA/SDLC Link/iX (30291B and A5563A) or
SNA/Token Ring Link/iX product (J2167B).
• A full-or half-duplex data communications
line (switched or leased) between the HP
3000 and the IBM mainframe or IBM
AS/400. A pair of synchronous modems.
or
An X.25 connection to the IBM mainframe
(X.25 not supported to IBM AS/400).
• A block mode terminal that is supported by
VPLUS/3000 for configuration.
• A COBOL II, PASCAL, C (HP LU 6.2 API/iX
only), or Transact compiler.
Representative for specific Communication
Controller model support.)
IBM Mainframe Software Requirements:
• Advanced Communication Function for the
Virtual Telecommunications Access Method
(ACF/VTAM) applications are supported
with:
– Mapped LU 6.2 conversations only
– ACF/VTAM version 3.2 or later
– MVS operating system
– Advanced Communication Function for
the Network Control Program (ACF/NCP)
remote transmission control program ver-
sion 3.1 or later.
• Customer Information Control System
(CICS) applications are supported with:
– Mapped LU 6.2 conversions only
– CICS version 1.7 or later
Installation and Configuration Policy
The Customer is responsible for loading the
HP LU 6.2 API software onto the system.
Hewlett-Packard will perform minimum
configuration of HP LU 6.2 API in order to
verify minimum product functionality. This
activity is included in the product purchase
price.
Customer Responsibility
– ACF/VTAM version 2.1 or later
• MVS or DOS/VSE operating system
The customer is responsible for performing
the following tasks in order to successfully
install and configure HP LU 6.2 API:
IBM AS/400 Hardware Requirements:
• An IBM AS/400.
• A port on the AS/400 that supports an
SNA line.
• Providing HP with the information neces-
sary to complete the Network
Implementation and Support Plan (NISP),
including:
IBM AS/400 Software Requirements:
• OS/400 Version 1.2 or later.
– System configurations
– Logical network map identifying relevant
traffic flow
HP 3000 product requirements:
• For HP LU 6.2 API/iX:
HP
3000
Bus ness
Servers
17
– Physical network map identifying relevant
network hardware components.
Additional Implementation
Assistance
• Verifying that the necessary host mainframe
or AS/400 software is installed and config-
ured to support HP LU 6.2 API. The cus-
tomer should consult the “HP SNA Products
Remote System Configuration Guide”
(P/N J2220-61025), or the “HP SNA
Products: AS/400 Guide” (P/N 5960-1629)
for details.
• Verifying that SNA Link/V, SNA/SDLC
Link/iX, or SNA/X.25 Link/iX is properly
installed and configured prior to the instal-
lation of HP LU 6.2 API.
• Updating the HP 3000 system to the proper
release level and installing the HP LU 6.2
API software using AUTOINST. Refer to the
HP 3000 MPE/iX Installation and Update
Manual (36123-90001) for MPE/iX systems
or the HP 3000 Software Update Manual
(32033-90036) for MPE V systems.
• Verifying that all of the necessary software
modules have been successfully installed by
AUTOINST and are at the correct version
levels using the NMMAINT.PUB.SYS utility.
• Configuring HP LU 6.2 API in order to fully
integrate HP LU 6.2 API into the existing
customer network.
For implementation needs that go beyond
installation, the customer can either provide
self-support, or can purchase additional
services from HP. These services include
Network Startup and HP ConsultLine. In
addition, the customer can also purchase
service from HP on a time-and-materials basis.
Network Startup includes implementation
scheduling and coordination assistance,
network configuration and verification testing,
and network documentation.
Support Products
HP offers a spectrum of support service
products to help plan, implement, operate,
and manage your multivendor network
throughout the network lifecycle.
For more information, contact your HP Sales
Representative, or refer to the HP data sheets
for specific support services.
Documentation
HP Responsibility
For both HP LU 6.2 API/V and HP LU 6.2 API/iX:
• J2220-61025 HP SNA Products Remote
System Configuration Guide
Following the installation of HP LU 6.2 API,
HP is responsible for the following:
• 30294-61000 HP LU 6.2 API:
• Application Programmer’s Reference Manual
• Confirming that all of the necessary soft-
ware modules have been installed and are at
the correct version level.
• Configuring 1 LU with ‘Unsolicited Bind’
equal to ‘Y’.
• Starting the APPC subsystem and verifying
that the LU is in a PENDING or ACTIVE
state.
These steps complete HP’s portion of the
installation and minimum configuration of
HP LU 6.2 API.
For HP LU 6.2 API/iX:
• 5960-1629 HP SNA Products: AS/400 Guide
• 30294-61002 APPC Subsystem on MPE/iX
Node Manager’s Guide
For HP LU 6.2 API/V:
• 30253-90002 LU 6.2 API/V Node Manager’s
Guide
• 30253-90004 APPC Subsystem on MPE V
Node Manager’s Guide
HP
3000
Bus ness
Servers
18
Features
SNA Distributed Host Command Facility
•
•
•
SNA DHCF/iX provides IBM 3270
display stations with HP terminal
capabilities including support for TTY-
mode (simple ASCII) applications and
many VPLUS applications.
VPLUS has been optimized for
applications used with SNA DHCF/iX;
VPLUS forms can be compiled into
IBM 3270 terminal formats prior to
runtime.
SNA DHCF/iX provides HP terminal
emulation support for screen sizes of
24, 32, or 43 lines for TTY-mode
applications. VPLUS applications are
supported with screens of up to 24
lines less any lines required for a
window line or softkeys.
In VPLUS applications, SNA DHCF/iX
supports HP terminal softkeys (as PF
keys) and a “window” line on IBM
3270 display stations using the
bottom three lines of the screen.
One MPE/iX session is provided for
every SNA DHCF/iX user; each SNA
DHCF/iX session appears as a
Network Services Virtual Terminal
(NS VT) session.
The HP SNA Distributed Host Command Facility/iX (HP
SNA DHCF/iX) software product provides IBM mainframe
users who use IBM 3270 display stations with interactive
access to an HP 3000 Series 900 system. Together with
the IBM Host Command Facility (HCF Version 2) product
on the IBM mainframe system, SNA DHCF/iX gives IBM
3270 display station users the capability to run many
applications on the HP 3000 system. These applications
include TTY-mode and VPLUS applications.
SNA DHCF/iX provides the data conversion services that
translate output between applications on the HP 3000 and
the IBM 3270 datastream required by IBM display stations.
SNA DHCF/iX enables IBM 3270 display station users to
access the HP 3000 system over their existing SNA, Token
Ring, or X.25 network. SNA DHCF/iX requires the
installation and use of the SNA/SDLC Link/iX (30292B and
A5563A), SNA/Token Ring/iX (J2167B)*, or the SNA/X.25
Link/iX (36939B) product (referred to jointly as SNA
Link). SNA Link products manage the physical link to the
IBM mainframe and implement the datacomm protocols in
the lower three layers of SNA.
•
•
* SNA/Token Ring Link/iX (J2167B) requires MPE/iX
release 5.5 Express 5 or later, or MPE/iX release 6.0
Express 1 or later.
•
•
SNA DHCF/iX supports the HP “Break”
and “Control-Y” keys.
SNA DHCF/iX can support up to 64
simultaneous sessions per SNA Link
node. Using multiple SNA Link nodes,
SNA DHCF/iX’s session count is
limited only by the number of LDEVs
available on the HP 3000
Other HP SNA Service products are
supported over the same SNA Link;
each SNA Link can support up to
64 Logical Unit (LU) sessions. The
maximum line speed supported by
SNA Link is 64 KB/s.
IBM S/370
Mainframe running
Host Command Facility
•
Communications
Controller
•
•
•
SNA DHCF/iX users can access
HP MM II applications on the
HP 3000.
SNA DHCF/iX provides a full screen,
ISPF-like editor for use by
HP DeskManager users.
SNA DHCF/iX contains a
comprehensive and flexible logging
facility that records SNA DHCF/iX
session and error messages.
SNA Link(s)
Other HP
DHCF/iX SNA Services
IBM
3174
SNA
HP 3000/iX
SNA DHCF/iX
Logical Session
IBM 3270 Display Stations
HP
3000
Bus ness
Servers
19
When the VPLUS forms have been designed
and are ready to be compiled, the applications
designer will select the “IBM 3270” box in the
Terminal Selection Menu of FORMSPEC, in
addition to any HP terminal options normally
selected, in order to include the IBM 3270
format in the VPLUS forms file. Please note
that, in an existing application, some VPLUS
forms may need to be modified due to
limitations of the IBM 3270 display station.
Many of the VPLUS forms may require no
changes.
Functional Description
HP SNA DHCF/iX is a software product that
provides an IBM 3270 display station with
access to applications on an HP 3000. SNA
DHCF/iX emulates many features of a
remotely attached HP terminal; thus, it
appears as if the IBM 3270 display station has
a direct connection to the HP 3000 computer.
SNA DHCF/iX can be operated across an
existing SNA or X.25 network.
SNA DHCF/iX communicates with Host
Command Facility (HCF) on the IBM
Usage Considerations
mainframe in order to exchange data between
the user’s MPE session and the IBM terminal.
To the HP 3000 system, each SNA DHCF/iX
session appears as a NS VT session. For IBM
3270 display stations, SNA DHCF/iX provides
access to two primary groups of applications
on the HP 3000 Series 900 system.
HP SNA DHCF/iX is not a complete
replacement for HP terminals such as the HP
700/92 and HP 700/94 terminals. Due to
limitations of the IBM 3270 display station,
SNA DHCF/iX cannot support all HP 3000
applications. In addition, some HP 3000
applications may require modifications prior
to use with SNA DHCF/iX. Please refer to the
SNA DHCF/iX Application Programmer’s
Guide for information on usage considerations
discussed here.
• TTY-mode applications are characterized by
their simple use of terminal control charac-
ters (carriage return, line feed, form feed,
tab, bell). SNA DHCF/iX translates the data
as output being sent to the IBM terminal.
This group of applications includes the basic
MPE/iX CI (Command Interpreter) com-
mands.
The HP keyboard differs from the IBM
keyboard. The chart below shows some
differences.
HP Terminals
HP Function Keys
IBM Terminals
IBM PF Keys 1-8 (VPLUS
Applications only)
• VPLUS applications are characterized by
the use of the VPLUS forms subsystem that
is included with the MPE FOS. VPLUS has
been enhanced so that an applications pro-
grammer can design VPLUS-based applica-
tions for the IBM 3270 display station in
addition to other HP terminals.
Consequently, IBM 3270 display station
users can be provided with access to many
VPLUS-based applications using SNA
DHCF/iX.
Security fields,
Full-Bright and
Half-Bright fields
Previous Page Key,
Next Page Key,
Insert Line Key, and
Delete Line Key
HP terminal characters: IBM Terminal mapping:
Equivalent functions provided
No equivalent functions
provided for IBM terminals
Break
Control-Y
Hard RESET
PA1
PA2
CLEAR
When developing VPLUS applications for use
with SNA DHCF/iX, the application designer
can develop and modify VPLUS forms using
techniques similar to those for HP terminals.
HP
3000
Bus ness
Servers
20
HP 3000 applications that use special screen-
mode or block-mode features that are specific
to HP terminals are not supported. Some of
these restrictions include:
If the target application violates any of these
restrictions, then it is not supported by SNA
DHCF/iX. An error condition will be returned
to the application when an unsupported
feature is used. Prior to installation of SNA
DHCF/iX, target HP 3000 applications should
be qualified to ensure that they meet these
restrictions.
• HP terminal escape sequences used for cur-
sor positioning, terminal strap settings, pro-
grammable softkeys, etc.
• Screen enhancements such as inverse video,
blinking, underlining, etc.
When using SNA DHCF/iX, IBM 3270 display
station users may experience different
performance and functionality than HP
terminal users. For IBM 3270 display stations,
response times may be somewhat greater than
an HP terminal due to the SNA network
overhead.
SNA DHCF/iX can provide universal access to
HPDESK for an integrated office automation
solution.
Within VPLUS applications, SNA DHCF/iX
supports all of the VPLUS intrinsics except for
VPRINTSCREEN and VPRINTFORM. Due to
limitations of the IBM 3270 display station,
VPLUS forms caching is not supported with
SNA DHCF/iX. In addition, several points
need to be considered in VPLUS forms design
including:
Functional Specifications
• SNA DHCF/iX supports many of the basic
functions of HP terminals. Please refer to
the Usage Considerations section for fea-
tures that are not supported. Supported fea-
tures include:
• Prior to using a VPLUS application with
SNA DHCF/iX, the VPLUS forms file must
be recompiled using the ‘IBM 3270’ terminal
option.
• When using FORMSPEC to design VPLUS
forms, an HP terminal such as the HP
700/94 is required.
• Unlike HP terminals, IBM 3270 display sta-
tions require an actual space on the screen
for an attribute byte that describes the
attributes of the following field.
• Each field on the IBM display station needs
to be preceded by this attribute byte; conse-
quently, back-to-back fields are not allowed
on the IBM 3270.
– Modified Data Tags
– Security Fields
• SNA DHCF/iX supports three different dis-
play enhancements for IBM 3270 display
stations: full-bright, half-bright, and non-dis-
play. (Non-display is for security fields.)
• SNA DHCF/iX supports those IBM devices
officially supported by IBM for the Host
Command Facility, Version 2. Please refer to
IBM’s HCF Product Specification Guide
(GC27-0647) for a complete listing.
• Each SNA DHCF/iX session appears as a
Virtual Terminal session. The pool of Virtual
Terminal sessions available for other users
will be reduced by the number of SNA
DHCF/iX sessions that are currently active.
• SNA DHCF/iX can support multiple simulta-
neous sessions, depending upon the number
of VT sessions or LDEVs (depending on the
MPE/iX release) distributed across multiple
SNA Links.
• With SNA DHCF/iX, a VPLUS form can have
at most 24 lines; if features such as softkeys
(two lines) or a window line (one line) are
used in the application, then the available
lines for the form are reduced by the num-
ber of lines required by these features.
• Each SNA Link can support up to 64 con-
current sessions distributed among the vari-
ous SNA/iX services.
HP
3000
Bus ness
Servers
21
• Using an HP 3000 Series 900 and SNA
DHCF/iX as a gateway system, IBM 3270
display stations can access only TTY-mode
applications on other HP 3000 MPE/iX sys-
tems. Access to other systems requires the
NS Network Service and Link products.
• SNA DHCF/iX supports “reverse VT” func-
tionality; this permits an HP application to
acquire remote IBM 3270 display stations
provided that the SNA DHCF/iX session has
already been established.
HP will support certain versions and later
releases of the above software. Your HP
support representatives must determine
whether SNA DHCF/iX can be supported with
your network configuration. The Network
Implementation Support Plan (NISP) will
assist the HP account team in determining
support requirements prior to the installation
of SNA DHCF/iX.
Installation and Configuration Policy
Product Requirements
The customer is responsible for loading the
SNA DHCF/iX software onto the system.
• Hewlett-Packard System Requirements
– HP 3000 Series 900 Computer System
– A supported release of MPE/iX
– SNA/SDLC Link/iX (30292B and A5563A),
SNA/Token Ring Link/iX (J2167A), or
SNA/X.25 Link/iX (36939B)
Hewlett-Packard will perform minimum
configuration of SNA DHCF/iX in order to
verify minimum product functionality. This
activity is included in the product purchase
price.
• SNA DHCF/iX requires an IBM System/370
or compatible mainframe with an IBM 37xx
communications controller. SNA DHCF/iX
has been certified with the following mini-
mum levels of IBM software for the IBM
mainframe and communications controller:
– MVS (OS/VS2 Release 3.8)
Customer Responsibility
Prior to having HP personnel onsite to
perform minimum configuration of SNA
DHCF/iX, the customer is responsible for the
following:
– ACF/VTAM Release 3.2 or later
– ACF/NCP Release 5.2 or later
– HCF
• Providing HP with the information neces-
sary to complete the Network
• For communication to an IBM S/36 the fol-
lowing software must be running on the IBM
system:
Implementation and Support Plan (NISP)
including:
– system configurations
– SNA 3270 Emulation
– logical network map identifying relevant
traffic flow
• HCF V2 (Host Command Facility, Version 2
- IBM P/N 5668-985) must be installed on
the IBM host. IBM supports HCF V2 under
MVS as well as OS/VS1 and DOS/VSE (see
below) operating environments.
• Although IBM supports HCF V2 under the
OS/VS1 Release 7.0 and DOS/VSE Release
35 operating environments, HP SNA
DHCF/iX has not been tested or certified
with these operating systems.
– physical network map identifying relevant
network hardware components.
• Verifying that the necessary host mainframe
software is installed and configured to sup-
port SNA DHCF/iX. The customer should
contact their HP Sales Representative for
typical host parameter values or consult the
“HP SNA Products Remote System
Configuration Guide” (J2220-61025) for
details.
HP
3000
Bus ness
Servers
22
• Verifying that SNA Link is properly installed
and configured prior to this installation of
SNA DHCF/iX unless SNA Link will be
installed at the same time.
• Updating the HP 3000 system to the proper
release level and installing the SNA
DHCF/iX software using AUTOINST. Refer
to the HP 3000 MPE/iX Installation and
Update Manual (36123-90001).
• Verifying that all of the necessary software
modules have been successfully installed by
AUTOINST and are at the correct version
levels using the NMMAINT.PUB.SYS utility.
• Performing full system backups as neces-
sary and ensuring that the HP 3000 system
and personnel with HP 3000 system man-
agement knowledge are available when HP
is onsite to complete the minimum configu-
ration of SNA DHCF/iX.
Additional Implementation
Assistance
For implementation needs that go beyond
installation, the customer can either provide
self-support or can purchase additional
services from HP. These services include
Network Startup and HP ConsultLine. In
addition, the customer can also purchase
service from HP on a time-and-materials basis.
Network Startup includes implementation
scheduling and coordination assistance,
network configuration and verification testing,
and network documentation.
Ordering Information
Product/Option
Number
A5563A
010
Description
SNA Link Interface Card
RS-232-C Synchronous
Modem Connection
V35 Synchronous
Modem Connection
Autodial Connection
Factory Integration
The customer is also responsible for
completing the configuration in order to fully
integrate SNA DHCF/iX into the existing
customer network after HP has completed the
minimum configuration of SNA DHCF/iX.
020
025
0D1
HP Responsibility
Required for SNA/SDLC, SNA/Services bundle, NS
Point-to-Point, RJE, BSC/iX Softwares (option 001
CIB/CIO become obsolete)
Following the installation of SNA DHCF/iX,
HP is responsible for the following:
Product/Option
Number
30292B
• Confirming that all of the necessary soft-
ware modules have been installed and are at
the correct version level.
Description
SNA Services License,
Software and Documentation
• Configuring the SNA DHCF/iX product to a
minimum configuration (1 LU) in order to
verify software and hardware functionality.
• Verifying the SNA DHCF/iX configuration by
issuing the DHCFCONTROL START com-
mand and ensuring that the LU to SSCP
session becomes active for the LU that was
configured.
310
330
340
Tier 1 License (also applies to 315,
320 Tier 2, 3 systems)
Tier 4 License (also applies to 335
Tier 5 systems)
Tier 6 License (also applies to 350
Tier 7 systems)
Upgrade credit Tier 1
Upgrade credit Tier 4
0CD
0CF
Requires A5563A.
Includes former 30202A, 30293A, 30294A, and 36935A.
These steps complete HP’s portion of the
installation and minimum configuration of
SNA DHCF/iX.
Customers must also order the MPE media
product (51543B) on MPE/iX 5.5 Express 7 or
later, or MPE/iX 6.0 Express 1 or later. This is
required to receive software for this product.
HP
3000
Bus ness
Servers
23
Support Products
HP offers a spectrum of support service
products to help plan, implement, operate,
and manage your multivendor network
throughout the network lifecycle.
For more information, contact your HP Sales
Representative, or refer to the HP data sheets
for specific support services.
Documentation
The following documentation is for SNA
DHCF/iX:
• 36935-61001 HP SNA DHCF/iX User
Support Guide
• 36935-61002 HP SNA DHCF/iX Node
Manager’s Guide
• 36935-61003 HP SNA DHCF/iX Application
Programmer’s Manual
• 36935-61004 HP SNA DHCF/iX Diagnostic
Message Manual
• J2220-61025 HP SNA Products Remote
System Configuration Guide
HP
3000
Bus ness
Servers
For additional information please contact any of our
worldwide sales offices or HP Channel Partners.
For direct country contact call:
Argentina: +541 787 7145
For the location of the nearest sales office call:
Austria: +43 1 25 000 0
United States of America:
Hewlett-Packard Company
+1 800 637 7740
Belgium and Luxembourg: +32 2 778 31 11
Brazil: +5511 7296 8000
Chile: +562 203 3233
Hewlett-Packard Company
5201 Tollview Drive
Columbia: +571 629 5030
Rolling Meadows, IL 60008
+1 847 245 3030
East Central Europe, CIS, and Yugoslavia: +43 1 25 000 0
Denmark: +45 45 99 10 00
Hewlett-Packard Company
5245 Pacific Concourse Drive
Los Angeles, CA 90045
+1 310 535 2600
Finland: +358 9 887 21
France: +33 1 69 82 60 60
Germany: +49 7031 140
Hewlett-Packard Company
20 Perimeter Summit Boulevard
Atlanta, GA 30319-1417
+1 404 648 5000
Greece: +30 1 689 644
Hungary: +36 1 252 7300
Iceland: High Performance Systems hf. +354 1 67 10 00
Ireland: +353 12 88 33 99
Canada:
Hewlett-Packard Ltd.
5150 Spectrum Way
Mississauga, Ontario L4W 5G1
Canada
Israel: Computation and Measurement Systems (CMS) Ltd.
+972 3 5380 333
+1 905 206 4725
Italy: +39 2 92122770
J apan:
Mexico: +525 326 4600
Hewlett-Packard Japan, Ltd.
Korakuen Shinjuku Bldg., 4-15-7
Nishi-Shinjuku, Shinjuku-ku
Tokyo, 160, Japan
Netherlands: +31 20 547 6911
Norway: +47 22 7356 00
+81 3 5371 1342
Poland: +48 22 608 77 00
Portugal: +351 1301 7343
Russia and the CIS, Excl. Ukraine: +7 095 923 5001
Slovenia: +38 61 55 84 72
Spain: +34 1 631 1600
Latin America:
Hewlett-Packard
Latin American Region Headquarters
Waterford Building, 9th Floor
5200 Blue Lagoon Drive
Miami, Florida 33126 USA
+1 305 267 4220
Sweden: +46 8 444 2000
Refer to country phone numbers
Switzerland: +411 735 7111
Australia/New Zealand:
Hewlett-Packard Australia Ltd.
31-41 Joseph Street
Blackburn, Victoria 3130
Australia (A.C.N. 004 394 763)
+61 3 9272 2895
South Africa: Hewlett-Packard South Africa (Pty) Ltd.
+27 11 806 1000
Turkey: +90 312 468 8770
United Kingdom: +44 1344 369231
Venezuela: +582 239 4133
Asia Pacific:
Hewlett-Packard Asia Pacific Ltd.
17-21/F, Shell Tower
Times Square,
1 Matheson Street
Causeway Bay,
Hong Kong
+8522 599 7777
The information contained in this document is subject
to change without notice.
Europe/Africa/Middle East:
Hewlett-Packard S.A.
150, Route du Nant-d’Avril
CH-1217 Meyrin 2
Geneva, Switzerland
+41 22 780 81 11
©Copyright Hewlett-Packard Company 1999
All Rights Reserved. Reproduction, adaptation,
or translation without prior written permission is
prohibited except as allowed under the copyright laws.
Printed in USA RO0499
5968-4833E
HP
3000
Bus ness
Servers
|
Graco Baby Playpen ISPP056AA User Manual
Graco Stroller PD162496B User Manual
Haier Refrigerator HDF05WNAWW User Manual
Harbor Freight Tools Kitchen Utensil 92390 User Manual
Harbor Freight Tools Paint Sprayer 43760 User Manual
Hasselblad Camera Lens HC 35 35 User Manual
HP Hewlett Packard All in One Printer 7140xi User Manual
HP Hewlett Packard Flat Panel Television LC3760N User Manual
Ikelite Digital Camera Coolpix L1 User Manual
Image Home Gym HGBE89910f User Manual